A blender is a common kitchen appliance that can be used to make smoothies, shakes, and purees. While it is easy to use, cleaning a blender can be a challenge. This is because the blades are sharp and can be difficult to reach. However, with a little bit of effort, it is possible to clean a blender and get it looking like new
Methode:1 Cleaning the carafe
Mix dish soap:
Add a drop or two of dish soap to the jar and fill it about halfway with warm water. Put all of the parts back on the blender and give it a good whirl until everything is nice and foamy. Rinse everything off again and dry thoroughly before putting away.
Use lemon to remove stains:
Lemon is a natural cleaning agent that can be used to remove stains. To use lemon to remove stains, simply cut a lemon in half and rub it on the stain. The acid in the lemon will break down the stain and lift it from the surface. Lemon is also effective for cleaning blenders. To clean a blender with lemon, cut a lemon in half and insert it into the blender. Blend on high for 30 seconds. The lemon will disinfect the blender and leave it smelling fresh.
Scrub stubborn stains:
Make a paste of baking soda and water and apply it to the areas that need cleaning. Let it sit for a few minutes before scrubbing with a brush or sponge. If the stains are still there, you can try using white vinegar or lemon juice. Just be sure to rinse well after using either of these cleaners.
Allow the blender to air dry:
First, unplug the and take out the detachable parts, like the pitcher and blade assembly. Have dishwasher-safe parts, so you can just pop them in the dishwasher. If yours is not dishwasher-safe, soak all of the parts in hot, soapy water for about 15 minutes before scrubbing with a sponge or brush.
Read more: How to Clean Microwave Oven
Methode:2 Clean the base
Wipe down the base:
First, unplug and remove the jar. Then, using a damp cloth, wipe down the base. Be sure to get into all the nooks and crannies – a toothbrush can help with this. Once you’ve wiped it down, dry it off with a clean towel.
Clean the base before drying it:
Once the base is clean, you can dry it with a towel or let it air dry. If you notice any rust on the base, you can remove it with a mild abrasive, such as baking soda. Once the base is dry, you can screw it back onto and start using it again.
Use a Q-tip to clean the control buttons:
Dip a Q-tip in rubbing alcohol and use it to clean the control buttons. Be sure to get in all the nooks and crannies.
Once you’re finished cleaning the buttons, wipe down the outside with a damp cloth. You can disinfect it by wiping it down with a solution of one part vinegar and one part water.
Methode:3 Clean the blade
Remove and clean separately:
First, remove the blade assembly and soak it in warm, soapy water. While that’s soaking, you can clean the rest of the blender. Just add some dish soap to the blender jar and fill it with warm water. Let it run for a few minutes, then rinse it out thoroughly. To finish up, dry all the parts thoroughly before reassembling your blender.
Use Polydent tablets:
Just add one tablet to a cup of warm water and let it soak for a few minutes. Then, rinse the blender out with clean water and you’re done!
Lubricate the gasket:
The gasket is a small rubber ring that sits between the blade and the jar, and it’s what seals the blender so that liquid doesn’t leak out. Over time, the gasket can become dirty and gunked up with bits of food, which can make it hard for the blender to operate properly. To clean the gasket, simply remove and wash it with soap and water. If it’s particularly dirty, you may need to soak it in vinegar or bleach before scrubbing it clean. Once the gasket is clean, dry it off and put it back on the blender.
Pour water into the blender:
First, unplug and disassemble all of the removable parts. Be sure to wash the pitcher and lid in warm, soapy water. To clean the blades, fill the sink with hot water and detergent and let them soak for about 15 minutes. Then, use a brush to scrub away any remaining food or residue.
Add dish soap:
Start by adding a drop or two of dish soap. Then, add some warm water and put the lid on. Blend on low for 30 seconds to 1 minute. After that, remove the lid and rinse out the blender with clean water. Repeat if necessary.
Rinse with warm water:
To clean your blender, start by taking it apart and rinsing all the parts with warm water. Be sure to get into all the nooks and crannies, as this is where dirt and grime can build up. Once you’ve rinsed everything off, put all the parts back on and blend some water for 30 seconds to remove any leftover residue.
Take the blender apart
In order to properly clean your blender, you must first take it apart. Start by unplugging the device and removing the pitcher from the base. Next, twist off the blade assembly and remove any rubber gaskets. Wash all of the parts in warm, soapy water and rinse thoroughly. Allow everything to air dry completely before reassembling it.
Rinse the jar
To start, unscrew the jar from the base. Rinse the jar out with some warm water. Add a drop or two of dish soap and fill the jar up with water. Screw the jar back onto and blend on high for 30 seconds.
Wash other small pieces
First, make sure that all of the small pieces are washed. This includes the blades, the jar, and the lid. Next, you will want to fill your sink with warm water and dish soap. Then, add the small pieces to the sink and let them soak for a few minutes. After a few minutes have passed, take a scrub brush and scrub each piece clean.
Run blender for stuck items
First, check to see if the blades are inserted properly and that they’re not dull. If they seem fine, then try adding some liquid to the mix – this will help to lubricate the blades and make blending easier. Finally, if all else fails, you can try running for a longer period of time to break down the ingredients.
Reassemble the blender and save it
Disassemble all of the parts. You may need to use a brush or cotton swab to get into all of the nooks and crannies. Once everything is clean, dry all of the parts thoroughly.
Next, inspect each part for damage. If any of the blades are bent or broken, they will need to be replaced. The same goes for any cracked or chipped plastic parts. Once you have replaced all of the damaged parts, you can reassemble and give it a test run.
Tips for keeping the blender clean and fresh
1. Rinse the blender immediately after use. This will prevent food from drying and hardening on the blades and other parts of the appliance.
2. Use hot water and soap to wash once a week. This will remove any built-up grease or grime.
3. Periodically check the gasket (the rubber seal that goes around the blade assembly) for cracks or tears. If you find any damage, replace the gasket to prevent leaks.
4. Never put jar in the dishwasher as this can dull the blades over time.
Conclusion
The blender is a great kitchen tool that can be used to make a variety of different foods and drinks. If you are looking for a versatile and easy-to-use appliance. There are many different models on the market, so be sure to do your research to find the perfect one for your needs.
