Removing A bathroom basin stopper can be A simple task that can save you money and time. Over time, A bathroom plughole stopper can become clogged Or corroded, Making it difficult to drain water from the sink. In some cases, Removing the cork may be necessary to clean Or unclog the drain. Fortunately, Removing A bathroom basin cap is A relatively easy process that can be accomplished with just A few basic tools and A little bit of know-how. In this article, We’ll discuss some of the methods you can use to remove A bathroom sink stopper and get your sink flowing freely again.
How to identify the type of sink stopper?
The most common types of sink stoppers are pop-up stoppers, Push-and-pull stoppers And Lift-and-turn stoppers.
Pop-up stoppers are often found in bathroom sinks and are easy to identify by their visible knob at the back of the basin.
Push-and-pull stoppers require minimal effort to operate as they only need A gentle tug Or push for them to open Or close.
Lift-and-turn stoppers have two distinct parts: A lift rod that opens and closes the drain and A knob on top that controls water flow.
Tools And Materials Needed
- Pliers.
- Screwdriver.
- Drain snake or auger.
- Bucket or bowl.
- Rubber gloves.
- Cleaning solution.
Steps To Remove The Bathroom Sink Stopper
Step 1: Clear The Area Around The Sink
Clearing the area around the sink is an essential task that every homeowner should perform regularly.
Over time, Hair, Soap And other debris can accumulate in the basin And drain, Leading to clogs And other plumbing issues.
Fortunately, Removing A bathroom basin closure is relatively easy And can help you keep your sink clean And functional.
Step 2: Access The Sink Stopper Mechanism
Look under the sink and locate the pivot rod that connects the stopper to the clevis (A flat metal bar with holes in it).
Loosen the retaining nut on the pivot rod using pliers Or A wrench and pull the pivot rod straight out of the clevis.
Lift the closure out of the drain.
If the stopper doesn’t lift out easily, Use a pair of pliers to gently wiggle And pull the stopper until it comes out.
[Note: Some sink stoppers may have A set screw located on the side of the clevis. If your basin closure has A set screw, Loosen it with A screwdriver before following the steps above.]
Step 3: Remove The Retaining Nut
To remove the retaining nut, You will need to first locate it under your plughole.
Once you’ve located it, Use pliers Or A wrench to loosen it counterclockwise.
Be sure to hold onto the stopper with your other hand as you do this so that it doesn’t fall into the drain And become lost.
It’s essential to note that not all retaining nuts are created equal, Some may require specialized tools for removal.
Step 4: Remove The Sink Stopper
To start, Locate the pivot rod underneath your basin. This is typically located behind the faucet handle Or on one side of the basin. Once you’ve found it, Use pliers Or an adjustable wrench to loosen the nut holding it in place. Be careful not to damage any other components while doing this! Once the nut is loose enough, Slide out the pivot rod And set it aside.
Read More: How to Unclog a Bathroom Sink.
Clean And Reassemble The Sink Stopper
Remove the sink closure from the drain following the steps mentioned earlier.
Clean the stopper thoroughly with soap and water, Or a mild bathroom cleaner to remove any dirt Or buildup.
Use a toothbrush Or small brush to scrub any hard-to-reach areas of the stopper.
Inspect the rubber seal Or gasket on the closure and replace it if it’s damaged Or worn out.
Clean the pivot rod, Clevis, And retaining nut with soap and water, Or a mild bathroom cleaner.
Reinsert the pivot rod into the clevis and tighten the retaining nut using pliers Or a wrench.
If the stopper is still not functioning properly, Try adjusting the pivot rod by moving it up Or down in the clevis until the stopper sits flush with the washbasin.
[Note: If you’re having trouble with any of the steps above Or the sink closure still isn’t working properly after cleaning and reassembling, It may be helpful to consult the manufacturer’s instructions Or a professional plumber.]
Conclusion
In conclusion, Removing a bathroom sink closure may seem like A daunting task, But it is actually quite simple. By following the steps outlined above, You can easily remove your basin stopper in just A few minutes. Always exercise caution when handling any plumbing fixtures and use the appropriate tools for the job. If you encounter any difficulties Or have questions about your specific plughole stopper, Consult with A professional plumber. Keep your bathroom running smoothly by regularly cleaning and maintaining your sink stopper. Happy unclogging!
